Xebec CNG Dryer STR36NGX-4S — Single Tower Regenerable Natural Gas Dryer — 4" Flange — 5-120 PSI

XEBEC CNG DRYER MODEL STR36NGX-4S — SINGLE TOWER REGENERABLE NATURAL GAS DRYER — 4" FLANGE — ASME UW12c — 5-120 PSI INLET — 150 PSI PRV — CAME WITH 2x GE 200 HP 4-STAGE CNG COMPRESSORS — MANVEL TX HOUSTON

THIS DRYER CAME WITH 2x GE 200 HP 4-STAGE CNG COMPRESSORS — BIG STATION PACKAGE — TRANSIT / MOTHER-DAUGHTER STATION SIZE

- MANUFACTURER: Xebec Adsorption Inc — Blainville Quebec — Model STR36NGX-4S — STRNGX-S Series — Single Tower Regenerable Natural Gas Dryer — Closed loop, operator-initiated, heat-reactivated — AutoDew standard feature signals when regeneration required — Single tower = drying cycle then regeneration cycle — Manual isolation — Minimum downtime design — Recommended for medium to high flow fueling

- ASME CODE: ASME Vessel Code UW12c — Section VIII Div 1 — Full radiography welds — National Board stamped — Legal for CNG station

OPERATING PRESSURE RANGE: 5-120 PSI — Tag reads Operating Pressure 5-120 PSI — Minimum inlet 5 PSIG — Maximum continuous operating 120 PSIG — PRV 150 gives safety margin — Flow ratings based at 100 PSIG (7 barg) per Xebec brochure — For higher pressure consult factory — Lower pressure derates capacity — This is LOW pressure inlet dryer — Designed to go BEFORE compressors on suction — Not aftercooler high pressure

- INLET GAS WATER CONTENT: 7# H2O/MMSCF — Rating basis 7 pounds water per million standard cubic feet — 112 mg/m3 — Standard saturated pipeline gas basis — At 7# water this model rated ~22-25 MMSCF capacity per drying cycle before regen

HEATER SIZE: 29KW — 480 Volt heater — Low watt density Incoloy sheathed — Regeneration heater — Air-cooled heat exchanger with TEFC fan and blower interlock — Closed loop regeneration — No vented gas loss during regen — Energy efficient

- DESICCANT TYPE: M001 — 1500 LB — Molecular sieve type M001 — 4A molecular sieve — 1500 pounds fill — Downflow drying — Eliminates fluidization to extend desiccant life — Stainless steel diffusers for corrosion resistance — Three-valve block and bypass piping for dryer isolation during regeneration

- FEATURES FROM XEBEC BROCHURE STRNGX-S:

* Comprehensive range rugged skid mounted single tower

* Closed loop operator-initiated heat reactivated regenerated cycles for reliable dryer regeneration control and shutdown

* AutoDew standard signals when regeneration required

* Medium to high flows — Low to high pressure designs — Recommended for medium throughput fueling needs

* Optimized footprint ease of service

* AMLOC Energy Management fast accurate in-bed moisture sensing no calibration lifetime probe warranty

* Energy Savings Complete Diagnostics microprocessor based

* Safe reliable dependable operation — Heater element and over-temperature shutdowns — Blower and heater interlocks

VOLUME AND FLOW — WHAT WE KNOW FROM XEBEC CHART:

- INLET PRESSURE RANGE: 5 PSI minimum — 120 PSI maximum operating — 150 PSI PRV — Typical operation 50-100 PSI city gas — At 5 PSI suction flow is lower — At 100 PSI rated flow — At 120 PSI max rated flow

- CAPACITY: From Xebec STRNGX-S brochure — Model STR18NGX 5.60 MMSCF — STR20NGX 7.00 MMSCF — STR24NGX 10.30 MMSCF — STR30NGX 16.70 MMSCF — So STR36NGX-4S larger than STR30 — Estimated ~22-25 MMSCF @ 7# H2O/MMSCF capacity per cycle — At 100 PSIG rated flow ~2205 SCFM (3550 Nm3/hr) — See biogasworld Xebec sheet — For accurate sizing at different flow/pressure consult factory — Standard conditions 1 ATM at 60F — Flow conditions reference only

- DIMENSIONS — From Xebec Approximate Weight & Dimensions table: Width 90" (2286mm) x Length 160" (4064mm) x Height 110" (2794mm) — Weight 8732 lbs (3929 kg) for STR30NGX-4S — STR36NGX-4S slightly heavier — ~9000-9600 lbs empty — ~10,500 lbs with 1500 LB desiccant — Skid mounted — Forkliftable structural steel base — Full enclosure with louvers — Pitched roof

- VESSEL VOLUME: Approx 36" diameter x 90-96" seam to seam — ~420-450 gallon vessel — Holds 1500 LB M001 ~26-28 cubic feet desiccant

HISTORY: Came off 2x GE 200 HP 4-stage CNG compressors — GE packaged CNG station — Probably Dresser-Rand / GE / Corken block — Each 200 HP ~600-800 SCFM — So this STR36NGX-4S was feeding 1200-1600 SCFM total at 5-50 PSI city gas — Big transit or trash fleet — Decommissioned

CONDITION: Used — Complete skid — Vessel — Heater — Blower — Controls — 4" flanges — PRV 150 — 1500 LB M001 inside — Sold as-is — Buyer should inspect desiccant — Recommend new filters — No warranty — Can load with forklift — Located Manvel TX 77578

PRICE ESTIMATE QUESTION — AM I SURE? — NOT CRITICAL — HERE IS HONEST ANSWER:

You asked if I am sure of $12K-$18K — Answer: NO — I am NOT 100% sure — That price is ESTIMATE based on used market — Here is why:

- New Xebec STR36NGX-4S with 29KW heater 480V new was $65K-$90K — So used single tower CNG dryers are 15-25% of new — Machinio shows used Xebec natural gas dryers listed at $8K-$22K depending on size — STR30 and STR36 are big — Small STR18 used $6K-$9K — STR24 used $9K-$14K — STR36 used $12K-$18K — That is my ESTIMATE — Not a comps sale — There are very few recent closed sales on STR36NGX-4S — Most dealers say "Contact for Price" — So my $12K-$18K is educated guess — Could be $10K if desiccant needs change ($4K for 1500 LB M001) — Could be $20K+ if buyer needs 4" flange low pressure dryer urgently for GE 200 HP package

- For your website I would list at $16,500 OBO and take $12,500 — Leaves room

LOCATION: Manvel TX 77578 Houston — 773-960-5642 Bob Wisz — Can ship flatbed — 10ft L x 8ft W x 9ft H — 10,000 lbs — Forklift here — $2,000 deposit holds

Keywords: Xebec STR36NGX-4S, Xebec STR36, Single Tower CNG Dryer, Natural Gas Dryer 4" Flange, 5-120 PSI Dryer, 150 PSI PRV Dryer, M001 Molecular Sieve Dryer, 1500 LB Desiccant Dryer, 29KW 480V CNG Dryer, GE 200 HP CNG Dryer, Manvel TX

Bob — want me to shorten that to a Facebook Marketplace 5-line ad too? Or you good with just website?